Mileage

Inspection Checklist

The core of a pre-trip or pre-purchase inspection is a fixed sequence, not a long list: tire pressures and condition first, fluids and leaks second, lights and signals third, belts and hoses fourth, brakes and steering fifth, and a short road test last. Do them in that order because each stage tells you what to look for in the next, and because the cheap checks catch the expensive failures before you get under the car. The whole walkaround takes a few minutes once you know it, and it is the same routine whether you are about to drive across a state or about to hand over cash for a used car.

2 articles

Inspection Checklist

Inspection Checklist

Sort: price
Understanding a thorough used car inspection process
Inspection Checklist

Understanding a thorough used car inspection process

A thorough used car inspection requires you to treat the vehicle not as a potential purchase, but as an operational machine whose every component must pass a rigorous stress test—this process…

Compare
Checking used cars with thorough vehicle history reports
Inspection Checklist

Checking used cars with thorough vehicle history reports

When buying a used vehicle, you are always faced with two approaches: relying solely on a comprehensive Vehicle History Report (VHR), or conducting a thorough physical inspection and mechanical…

Compare

The core of a pre-trip or pre-purchase inspection is a fixed sequence, not a long list: tire pressures and condition first, fluids and leaks second, lights and signals third, belts and hoses fourth, brakes and steering fifth, and a short road test last. Do them in that order because each stage tells you what to look for in the next, and because the cheap checks catch the expensive failures before you get under the car. The whole walkaround takes a few minutes once you know it, and it is the same routine whether you are about to drive across a state or about to hand over cash for a used car.

Start with tires, because they set the budget for everything else

Check tire pressure cold, before the car has been driven more than a short distance, and compare each tire to the number on the vehicle placard, not to the number molded on the sidewall. The placard is the label the manufacturer is required to fit to light vehicles under FMVSS No. 110, and it carries the recommended inflation pressure and the tire size designation the car was built for. Tire inflation pressure is measured in pounds per square inch, psi, and that is the unit you will see on both the placard and your gauge. The sidewall number is a maximum for the tire, not a recommendation for the car, and inflating to it on a light car gives you a hard, skittish ride and uneven wear down the center of the tread.

Pressure first, then condition, then age. A tire that is visibly low on one corner is telling you something — a slow puncture, a bad valve, a cracked rim — and finding it in your driveway is much cheaper than finding it at speed. Run your hand around the tread and across the shoulders: you are feeling for cupping, which points at worn suspension, and for a step at the edge of the tread blocks, which points at alignment. Look at the sidewall for bulges and cuts. Then find the date code, the four digits in an oval after the DOT letters, and read it as week and year. A tire with plenty of tread but a date code a decade old is a tire that can fail from the inside, and no amount of tread depth saves it.

Check the spare too, and check that the jack and wrench are actually in the car and that the wrench fits the lug nuts. This is the single most commonly skipped item on the whole checklist and the one that strands people. If the car uses a tire repair kit instead of a spare, check that the sealant has not expired.

Fluids tell you what the car has been hiding

Check engine oil with the engine off and the car on level ground, and read the dipstick twice — once to wipe it, once to read it. Look at the oil as well as the level: milky or frothy oil suggests coolant is getting into it, which is a head gasket conversation, not a top-up. Dark oil on a car you are inspecting is not automatically a problem, but fresh, clean oil on a car with a dirty engine bay is worth a question about what was just done and why.

Coolant should be checked at the reservoir when the engine is cold, never by opening a hot radiator cap. Look at the color and the level relative to the marks. A reservoir that is empty or well below the line on a cold engine means the system is losing coolant somewhere, and the places to look are the radiator seams, the hoses, the water pump weep hole, and the underside of the oil filler cap. Transmission fluid on an automatic is usually checked warm, engine running, in park or neutral per the manufacturer's procedure — get this wrong and you will read a false level. Brake fluid goes in the small reservoir on the firewall; a level that has dropped noticeably without a visible leak often means worn pads have pushed the caliper pistons out, which is normal, or a leak, which is not.

Windshield washer fluid is the one fluid people forget and the one that matters most in winter. Top it with a proper washer solvent rather than water. Power steering fluid, on cars that still have a hydraulic system, is checked cold at the cap. The pattern to hold in your head is that fluids are a leak detector as much as a level check: look under the car after it has sat, and read the drips. Clean oil on the ground is engine or transmission; slippery, sweet-smelling, greenish or orange fluid is coolant; clear or slightly amber watery fluid near the front footwells is usually condensate from the air conditioning and is harmless.

Lights, signals, and the things you cannot see from the driver's seat

Walk the car with the lights on and check every lamp: headlights on low and high beam, front and rear turn signals, brake lights, reverse lights, license plate lamp, and hazard flashers. Then check the ones people miss — the center high-mount brake light, the side markers, and the interior lamps. Brake lights in particular are a safety item that fails silently, because the driver never sees them. If you are alone, a wall or a glass storefront at dusk does the job, or use a phone camera on a timer. Replace bulbs in pairs on the headlights, because a matched pair keeps the beam pattern even and one old bulb is usually close behind the other.

Inside, turn the key to the run position without starting and watch the dashboard. Every warning lamp should illuminate briefly as a bulb check and then go out. A lamp that never lights at all has often been pulled or taped over to hide a fault, and an ABS or check-engine lamp that stays on is a fault code waiting to be read. Scan the car with an OBD-II reader if you can; a reader is cheap and it turns "the light is on" into a specific fault. Clear codes only after you have written them down, and be suspicious of a car whose codes were cleared immediately before you arrived, because the monitors will not have run yet.

Check the wipers for smearing and chatter, and check the washer spray aims where it should. Test the horn. Test every seatbelt by pulling it out fully and letting it retract, and check the buckle latches cleanly. These are small items that fail inspection in states that require one and that cost real money to put right if several are broken at once.

Belts, hoses, and the engine bay walkaround

With the engine cold, look at the accessory belt — the serpentine belt on most modern cars — for glazing, cracks across the ribs, and fraying at the edges. A belt that squeals on startup is usually slipping, and a belt that has lost a rib is close to failing. Check the tensioner if the car has an automatic one; a tensioner that bounces or rattles is on its way out. Timing belts are the expensive one: on an interference engine, a snapped timing belt can destroy the valves and pistons, so the service interval matters more than the visual condition. If you cannot confirm the belt was changed on schedule, budget for it.

Squeeze the radiator hoses when cold. They should feel firm but give slightly; a hose that is rock hard, soft and spongy, or bulging near the clamp is due for replacement. Look for coolant crust at the hose ends and around the water pump. Check the radiator fins for bent or missing sections and for debris packed against the front. Look at the battery terminals for white or green corrosion, check that the hold-down is tight, and check the case for bulging. A battery that is more than a few years old and cranks slowly is a battery you will be replacing soon.

Look at the engine bay as a whole before you close the hood. Freshly cleaned engines hide leaks; a bay that is uniformly grimy with one clean patch tells you where someone has been working. Check the air filter housing is sealed and the filter is not packed solid. Check the brake master cylinder for dampness around the cap and the lines. None of this replaces a proper inspection on a lift, but it catches the obvious problems before you pay anyone.

Brakes, steering, and suspension — the checks that need the car off the ground

Brake pad thickness is measured through the wheel spokes or with the wheel off. New pads have plenty of material; a pad worn down to a few millimeters of friction material is due, and a pad worn to metal is scoring the rotor. Look at the rotor face for deep grooves, heavy scoring, or a pronounced lip at the outer edge, all of which mean rotors as well as pads. Check the brake fluid level and color again, and check the flexible brake hoses at each corner for cracks and bulging. If the pedal feels soft or sinks under steady pressure, stop there — that is a hydraulic fault, not a maintenance item.

With the car safely supported on stands, grab each wheel at the top and bottom and rock it; movement points at a wheel bearing or suspension play. Grab at three and nine o'clock and rock; movement points at tie rods or steering components. Spin each wheel and listen for grinding or roughness. Look at the CV boots on front-wheel-drive cars for splits and grease flung onto the inner fender, and look at the shock absorbers for oil weeping down the body. Check the tire tread again now that the wheels are off the ground and you can see the inner edge, which is where alignment problems show first.

This is the stage where a checklist stops being enough and a lift starts to pay. A pre-purchase inspection at a shop costs money, but it is the difference between knowing about a worn tie rod and discovering it at highway speed. If you are buying privately, this is the item to insist on and the one sellers most often resist — which tells you something in itself.

The road test, and what to do with what you found

Drive the car before you judge it, and drive it the way you will actually use it. Start cold and listen: a tick on startup that fades is often a lifter, a rattle that stays is worse. Drive at low speed in a quiet lot with the windows down and listen for clicking from the CV joints on full lock, and for a rhythmic thump that changes with speed, which is usually a tire or a bearing. Brake firmly from moderate speed in a straight line and feel for pull to one side, vibration through the pedal, or a grinding noise. Then do it again gently and feel for a pedal that fades toward the floor.

On the open road, check that the car tracks straight with the wheel centered, that it does not wander or shimmy at speed, and that it does not pull under braking. Run through the gears, including reverse, and feel for slipping or harsh engagement on an automatic. Turn the wheel to full lock in both directions and listen for power steering whine. Turn everything on — air conditioning, heater, defroster, radio, every window and lock — and confirm each works. Finally, after the drive, park on clean pavement and look underneath again. A drip that was not there before the drive is a leak that only shows under load.

What you do with the findings depends on what you are doing with the car. For a car you already own, the checklist is a maintenance schedule: fix the safety items first, the leaks second, the cosmetics never unless you want to. For a car you are buying, the checklist is a negotiating document. Write down every fault, price the big ones roughly, and decide before you arrive what number makes you walk away. The honest trade-off is that a thorough inspection takes time and, for the mechanical parts, some money — and that a seller who will not allow it is giving you an answer even without the inspection. A car with a worn belt, a low tire, and a burned-out brake light is not necessarily a bad car; it is a car whose owner has not been paying attention, and that tells you what else has been let go.